ADC-V720W Outdoor Camera Guide

This camera is discontinued but can still be added and viewed on Alarm.com account

Specifications

  • 1280 x 800 pixel video resolution
  • 40' night vision range
  • Field of view 77° Horizontal 54° Vertical
  • WiFi 802.11 b/g/n
  • Ethernet connection
  • Does not support PoE Power over Ethernet
  • Operating Temperature -4° F to 122° F

Factory Default

Warning! Erases everything, camera must be re-added to Alarm.com and WiFi configured

Remove plastic cover and hold Reset button 15 seconds until LED flashes red and green

ADC-V720W_Outdoor_Bullet_Camera_Factory_Default.jpg

Hardwire Connection to Router

Plug Ethernet cable into back of camera and back of customer network router

ADC-V720W_Outdoor_Camera_Connect_To_Router.jpg

WiFi Setup by WPS Enrollment

1. Hold WPS button 5 seconds, LED by button rapidly flashes green

ADC-V720W_WPS_Button.jpgADC-V720W_Outdoor_Bullet_Camera_Green_LED.jpg

2. Press and release WPS button on router or enable WPS in router programming

Router_WPS_Button.jpg

3. After 2 minutes camera LED turns green if successful or red if failure

ADC-V720W_Outdoor_Bullet_Camera_Green_LED.jpg

Add Camera using the Brinks Home™ App Website

Note: the camera must first be connected to Wi-Fi.

1. Log in to the Brinks Home App and press Video.

001_Brinks_Home_App__Desktop__Home.png

 

2. Select Settings.

002_Brinks_Home_App__Desktop__Video-Live_Video_Default.png

 

3. Scroll to the bottom of the page and select Add video device.

003_Brinks_Home_App__Desktop__Video_Settings.png

 

4. The camera should be detected. Enter the camera name, then select Install.

004_Brinks_Home_App__Desktop__Name_Camera_and_Install.png

 

5. The camera is added to the network, which can take several minutes.

005_Brinks_Home_App__Desktop__Cam_Configuration.png

 

6. When finished, select Live View to view images from a newly installed camera.

006_Brinks_Home_App__Desktop__Complete.png

 

 

Add Camera using the Brinks Home™ Mobile App

Note: The camera must first be connected to Wi-Fi.

 

1. Log in to the Brinks Home App and press Video (found under the menu icon in the top left corner.

001a_Mobile_App_Home_Clean.jpg 001b_Mobile_App_Menu_Clean.jpg

2. Select Settings by pressing the Gear icon in the upper, right-hand corner.

002a_Mobile_App_Video-Gear_Clean.jpg

 

3. Select Add video device, then select your compatible device type.

003a_Mobile_App_Add-Video_Clean.jpg 003b_Mobile_App_Select-Device_Clean

4. The camera should be detected. Enter the camera name, then select Next.

004a_Mobile_App_Name_Device_Clean.jpg

 

5. The camera may take several minutes to configure.

005a_Mobile_App_Connect_Device_Clean.jpg 005b_Mobile_App_Verify_LED_Clean.jpg

6. When finished, select Live View to view images from a newly installed camera.

006a_Mobile_App_Live_View_Clean.jpg

 

Troubleshooting

  • Power cycle the camera by unplugging and plugging in power adapter
  • Move closer to WiFi router
  • If issues persist, try resetting camera to factory defaults and reinstall

LED Reference Guide

  • All Off - No power
  • Green ON - Internet and Alarm.com connection, all OK
  • Green Flash = Local network connection, no Internet connection
  • Green Rapid Flash = WPS Enrollment mode is active
  • Red On - No local or Internet connection
  • Red Green Flash - Factory reset or firmware upgrade

Chat