ADC-V723 Outdoor Camera Guide

Specifications

  • 1920 x 1080 pixel video resolution
  • 117° vertical and horizontal field of view
  • 40' night vision range
  • WiFi 802.11 b/g/n
  • Micro SD slot (not functional at this time)
  • Operating Temperature -4° F to 122° F

mceclip0.png

Factory Default

Warning: erases everything, the camera must be re-added to your account.

To reset the camera to factor default, remove the cover and hold the reset button for 15 seconds until the camera clicks and the LED flashes red.

ADC-V723_Back_WPS_Button.png


Pre-installation Steps

This brief video reviews pre-installation steps for the Brinks Home Outdoor Camera (ADC-V723):

Wi-Fi Setup by WPS Enrollment

This brief instructional video demonstrates how to successfully pair the Brinks Home Outdoor Camera (ADC-V723) to a router using WPS mode:

Step-by-step instructions:

1. Hold the reset button for 3 seconds until the front LED flashes blue.

ADC-V723_Outdoor_Camera_WPS_Connection__adjusted_.png

2. Press and release the router's WPS button or enable WPS in router programming.

Router_WPS_Button_adjusted_.png

3. The LED on the camera may turn red during this step. Wait 2 minutes for the camera LED to flash then turn solid green if successful.

ADC-V723_Outdoor_Camera_Green_Light.jpg

Note: If WPS mode fails, try Access Point mode.

Wi-Fi Setup by Access Point

This brief instructional video demonstrates how to successfully pair the Brinks Home Outdoor Camera (ADC-V723) to a router using Access Point (AP) mode:

Step-by-step instructions:

1. Hold the reset button for 6 seconds until the front LED flashes white to begin AP mode. This will also happen automatically after powering up the camera.

2. Go to smartphone Wi-Fi settings and find ADC-V723 (xx:xx:xx) then press Connect.

Access_Point_01_WiFi_Smartphone.png Access_Point_02_WiFi_Connect.png Access_Point_03_WiFi_Connected.png

3. In a web browser, go to http://v723install/ then press Scan for Wi-Fi networks.

Access_Point_04_Find_Out_IP_Address.png Access_Point_05_Enter_IP_Address_in_Browser.png Access_Point_06_Connected_Press_Scan.png

4. Select Wi-Fi network, scroll up and enter your Wi-Fi credentials, press Submit, then OK.

Access_Point_07_Select_WiFi_Network.png Access_Point_08_Enter_Encryption.png Access_Point_09_Finished.png

5. Camera LED turns green if successful or red if failure

ADC-V723_Outdoor_Camera_Green_Light.jpg

Add Camera using the Brinks Home™ App Website

Note: the camera must first be connected to Wi-Fi.

1. Log in to the Brinks Home App and press Video.

001_Brinks_Home_App__Desktop__Home.png

 

2. Select Settings.

002_Brinks_Home_App__Desktop__Video-Live_Video_Default.png

 

3. Scroll to the bottom of the page and select Add video device.

003_Brinks_Home_App__Desktop__Video_Settings.png

 

4. The camera should be detected. Enter the camera name, then select Install.

004_Brinks_Home_App__Desktop__Name_Camera_and_Install.png

 

5. The camera is added to the network, which can take several minutes.

005_Brinks_Home_App__Desktop__Cam_Configuration.png

 

6. When finished, select Live View to view images from a newly installed camera.

006_Brinks_Home_App__Desktop__Complete.png

 

 

Add Camera using the Brinks Home™ Mobile App

Note: The camera must first be connected to Wi-Fi.

Video Instructions:

 

1. Log in to the Brinks Home App and press Video (found under the menu icon in the top left corner.

001a_Mobile_App_Home_Clean.jpg 001b_Mobile_App_Menu_Clean.jpg

2. Select Settings by pressing the Gear icon in the upper, right-hand corner.

002a_Mobile_App_Video-Gear_Clean.jpg

 

3. Select Add video device, then select your compatible device type.

003a_Mobile_App_Add-Video_Clean.jpg 003b_Mobile_App_Select-Device_Clean

4. The camera should be detected. Enter the camera name, then select Next.

004a_Mobile_App_Name_Device_Clean.jpg

 

5. The camera may take several minutes to configure.

005a_Mobile_App_Connect_Device_Clean.jpg 005b_Mobile_App_Verify_LED_Clean.jpg

6. When finished, select Live View to view images from a newly installed camera.

006a_Mobile_App_Live_View_Clean.jpg

 

Troubleshooting

  • Power cycle the camera by unplugging and plugging in power adapter.
  • Move closer to Wi-Fi router.
  • If issues persist, try resetting camera to factory defaults and reinstall.

LED Reference Guide

  • Off - no power
  • Flashing Blue - WPS enrollment mode enabled
  • Blue - privacy mode enabled, press and release corner privacy button
  • Red - no local or Internet connection
  • Flashing Red - not programmed
  • Flashing Red/Green - restoring factory defaults
  • Flashing Green - local network connection
  • Green - internet and Alarm.com connection

Chat