2GIG GoControl 2 - Programming a Motion Detector

1. Press the Brinks Home logo in the bottom right of the panel, enter Installer Code 1561, then press system configuration to go to Q1 Wireless Sensor Programming.

001c_Programming_-_Enter_Program_01_280x159.png 001b_User_Menu_-_Disarm_05_280x159.png 001a_Programming_-_Enter_Program_03_280x159.png

2. Press the right arrow to choose your new sensor number, choosing an open zone as indicated by a white space and number only, then press the down arrow to continue.

002b_Image_Sensor_Program_01a_275x156.jpg 002a_Image_Sensor_Program_01_275x156.jpg

3. Press the right arrow to select Sensor Type (03) Perimeter, then press the down arrow to continue.

003b_Image_Sensor_Program_02a_Interior_Follower_275x156.jpg 003a_Image_Sensor_Program_02_Interior_Follower_275x156.jpg

4. Press the right arrow to select your Equipment Code, then the down arrow to continue.

005b_Image_Sensor_Program_03a_9999_Image_Sensor_275x156.jpg 005a_Image_Sensor_Program_03_9999_Image_Sensor_275x156.jpg

5. Press shift, then learn, then insert batteries or press the tamper button several times on the motion detector. Wait 20-30 seconds and once the sensor is found press Ok, then the down arrow to continue.

*Alternatively, this step can be completed by manually entering the serial number on the back of the sensor.

006c_Image_Sensor_Program_04_Serial_1_275x156.jpg 006b_Image_Sensor_Program_04_Serial_3_275x156.jpg 006a_Image_Sensor_Program_04_Serial_2_275x156.jpg

6. Enter (0) new for the Equipment Age, then press the down arrow to continue.

007a_Image_Sensor_Program_05_Age_275x156.jpg

7. Loop Number will be (1) 1, then press the down arrow to continue.

008_Image_Sensor_Program_06_Loop_1_275x156.jpg

8. Leave the Dialer Delay set to the default of (1) enabled, then press the down arrow to continue.

009b_Image_Sensor_Program_07a_Delay_275x156.jpg 009a_Image_Sensor_Program_07_Delay_275x156.jpg

9. Press Insert, then the right arrow to select your desired voice descriptor. For additional words, press Insert again and repeat the steps.

*Alternatively: you may use a 3-digit code to jump to the word of your choice. Code #147 represents Motion Detector.

010b_Image_Sensor_Program_08_Description_1_280x159.jpg 010a_Image_Sensor_Program_08_Description_2_280x159.jpg

Enter up to 6 words, then press the down arrow to continue.

011_Image_Sensor_Program_08_Description_3_280x159.jpg

10. Press the right arrow to set Sensor Reports to (1) enabled, then press the down arrow to continue.

012b_Image_Sensor_Program_09_Disabled_275x156.jpg 012a_Image_Sensor_Program_09_Enabled_275x156.jpg

11. Press the right arrow to set Supervised to (1) enabled, and press the down arrow to continue.

011a.alt_2GIG_Q1_RF_Sensor_Programming_11_Supervision_278x158.png

12. Chime is typically left at (00) disabled for motion sensor chime. Press down to continue to the summary.

013a_2GIG_Q1_RF_Sensor_Programming_12_Chime_278x158.png

13. Press edit next to program another sensor, or press skip, end, and exit to complete the process.

013b_Image_Sensor_Program_10_Summary_1_275x156.jpg


Chat